For Loan ST1300 Swingarm Locknut Tool

roginoz

roginoz

Joined
Feb 23, 2007
Messages
1,100
Age
73
Location
Wichita, KS
Bike
'05 ST1300
I have the swingarm locknut tool (part #07ZMA-MCAA101 in the shop manual) available for loan to forum members. This is the cylindrical spanner that is used on the swingarm to remove or replace and torque the left pivot bolt locknut.

This tool allows you to hold the 19mm allen bolt in place while setting the proper torque on the locknut. I also have a 19mm allen socket that will fit inside the locknut tool, and (thanks to ST-Traveler) a six inch long 1/2" drive extension. You'll need a torque wrench capable of 72 lb-ft. (The right side pivot bolt calls for 80 lb-ft.)

There's no cost to borrow the tool. PM me if you need it, and I'll ship it to you. Send it back with payment for my shipping costs as soon as you're finished, and I'll put it back in the tool chest until someone else needs it.
 
Last edited:
Flying Couch:

I see on your profile that you're riding an ST1100. The swingarm wrench is for an ST1300; I don't think it will work on your bike. I'll check the shop manuals (we still maintain an 1100 in my garage) and see if I can check Andrew's bike (my old 1100) to see if it fits.
 
$112.33 according to a Google search for the part # provided. Just jumped in since it's a new comment,so I hope I didn't step on toes :)
 
The swingarm locknut tool is down in Florida, helping Brian replace his u-joint. I'll re-post when it's back home and available for loan again.
 
The swingarm tool kit is once again available. Thanks to ST-Traveler for adding a 6" extension for the allen socket.

PM if you need to borrow it.
 
Mike has finished his project, and the swingarm tool set is back from California. It's available for the cost of shipping. PM if you need it.
 
The swingarm tools are back from California, and available for loan again. I hope Joe's project went well.
 
Hello all,

I currently have the ST1300 swingarm locknut tool kit that I loaned from @John OoSTerhuis. I was going to mail it back to him, but he mentioned that I should post something on the forum to see if anyone else currently needs it so that I could mail it directly to them.

So, is anyone currently in need of the swingarm locknut tool kit?

Just let me know, and I can mail it to you!

Thanks,

Tanner
 
Just wanted to bump this thread in case anyone is looking for the kit! I do still have it, and can mail it to anyone who might need it!

Otherwise, @John OoSTerhuis would you like me to mail it back to you?

Thank you,

-Tanner
 
Hey Tanner, do you still have the tool? I'm about to swap the u joint on my 2012 st1300 and need it. Happy to pay for shipping to me!
 
nkoken said:
Hey Tanner, do you still have the tool? I'm about to swap the u joint on my 2012 st1300 and need it. Happy to pay for shipping to me!
Click to expand...
Hello, yes I do still have the swingarm tools, and can definitely mail them to you! Can you send me the address? Or, if you're able to, send me a PM with the address?

Thank you,

Tanner
 
Burttj03 said:
Hello, yes I do still have the swingarm tools, and can definitely mail them to you! Can you send me the address? Or, if you're able to, send me a PM with the address?

Thank you,

Tanner
Click to expand...
Hello, Do you still have the swingarm tool available? I have a 2006 ST1300.
Thanks for your time.
Tom
 
You must log in or register to reply here.
Back
Top Bottom